Yamyam: 1版をインポートしました

2018-06-28T20:49:18Z

1版をインポートしました

2012年5月16日 (水) 07:17にwiki>Pepribalによる

2012-05-16T07:17:56Z

新規ページ

=={{Menu|3D View|Curve}} menu==

This menu is available in the {{Literal|3D View}} header in edit mode, when the object being edited is a curve.

[[File:Ref-3DView-Menus-Curve.png|frame|right|Curve menu]]

==={{Literal|Delete...}} ({{Shortcut|x}})===
There are three options for deletion:
* {{Literal|Select}} deletes all the control points.
* {{Literal|Segment}} deletes the segment that connects the selected control points, disconnecting them. This results in 2 disconnected curves. This operation doesn't delete any control point. Selection should include only 2 consecutive points.
* {{Literal|All}} deletes all control points of the curve object.

==={{Literal|Toggle Cyclic}} ({{Shortcut|alt|c}})===
Toggles the cyclic property on/off for the curves with elements selected.

==={{Literal|Make Segment}} ({{Shortcut|f}})===
Connects 2 disconnected control points. These must be loose points, or the first/last point of a curve. If the points belong to different curves, these will be connected into one. If they belong to the same curve, this operation will be equivalent to toggling cyclic on for thar curve.

==={{Literal|Separate}} ({{Shortcut|p}})===
With this operation, all curves that have elements selected (control points or handles) will be separated into a different curve object.

==={{Literal|Add Duplicate}} ({{Shortcut|shift|d}})===
Duplicates the selected control points and sets them in traslation mode. If only a handle is selected, the full point will be duplicated too. Each set of connected points that result duplicated will define a single curve.

==={{Literal|Extrude Curve and Move}} ({{Shortcut|e}})===
If the selection consists of a control point which is connected to less than 2 points, a new point will be created and connected to the first. The new point is set initially in traslation mode.

{{clr}}

=={{Menu|3D View|Curve|Show/Hide}} submenu==

This submenu is equivalent to {{Menu|3D View|Mesh|Show/Hide}} submenu, for curve control points. However, a few things should be considered: you can only show or hide control points, as segments are always shown, unless all control points of the connected curve are hidden, in which case the curve is fully hidden (but normals are not).

=={{Menu|3D View|Curve|Proportional Editing Falloff}} submenu==

This submenu is equivalent to {{Menu|3D View|Mesh|Proportional Editing Falloff}} submenu, for curve control points.

=={{Menu|3D View|Curve|Proportional Editing}} submenu==

This submenu is equivalent to {{Menu|3D View|Mesh|Proportional Editing}} submenu, for curve control points.

=={{Menu|3D View|Curve|Segments}} submenu==

[[File:Ref-3DView-Menus-Curve-Segments.png|frame|right|Segments submenu]]

==={{Literal|Subdivide}}===
All those segments with both control points selected will be subdivided, so that a new control point will be inserted between each of those pairs. The number of cuts can be adjusted from the ''redo panel''.

==={{Literal|Switch Direction}}===
Switches direction of all the curves of the object that have at least one element selected.

{{clr}}

=={{Menu|3D View|Curve|Control Points}} submenu==

[[File:Ref-3DView-Menus-Curve-ControlPoints.png|frame|right|Control Points submenu]]

==={{Literal|Tilt}} ({{Shortcut|ctrl|t}})===
Lets you define the tilt of the selected control points. The tilt will be interpolated from point to point (you can check it with the normals). The tilt angle is defined interactively first, and then it can be adjusted in the ''redo panel'' ({{Literal|Angle}}).

==={{Literal|Clear Tilt}} ({{Shortcut|alt|t}})===
Brings the tilt of those selected control points back to 0.

==={{Literal|Separate}} ({{Shortcut|p}})===
It's equivalent to {{Menu|3D View|Curve|Separate}}.

==={{Literal|Set Handle Type}} ({{Shortcut|v}})===
In bezier curves lets you set the handle type for all the selected control points (the same curve can have different kinds of handles):
* {{Literal|Automatic}}: handle values are recalculated always depending on the position of control points so that the curve has the smoothest shape possible. If the handle is manipulated, it stops being automatic (it goes aligned).
* {{Literal|Vector}}: handle values are recalculated always depending on the position of control points so that the curve has flat (straight) sides. If the handle is manipulated, it stops being vector (it goes free); in this case, the other side of the handle still remains vector.
* {{Literal|Aligned}} is a user-defined handle, in which both sides are always aligned.
* {{Literal|Free}} is a user-defined handle, in which both sides are independent.
* {{Literal|Toggle Free/Align}} toggles from free to aligned type.

{{clr}}

=={{Menu|3D View|Curve|Control Points|Hooks}} ({{Shortcut|ctrl|h}}) submenu==

This submenu is equivalent to {{Menu|3D View|Mesh|Vertices|Hooks}} submenu, for curve control points.

=={{Menu|3D View|Curve|Snap}} ({{Shortcut|shift|s}}) submenu==

This submenu is equivalent to {{Menu|3D View|Mesh|Snap}} submenu, for curve control points.

=={{Menu|3D View|Curve|Mirror}} ({{Shortcut|ctrl|m}}) submenu==

This submenu is equivalent to {{Menu|3D View|Mesh|Mirror}} submenu, for curve control points. In this case, {{Literal|Mirror Vertex Group}} is disabled as there is no such thing as control point groups.

=={{Menu|3D View|Curve|Transform}} submenu==

This submenu is equivalent to {{Menu|3D View|Mesh|Transform}} submenu, for curve control points.

← 古い版	2018年6月28日 (木) 20:49時点における版
(相違点なし)

利用者:Pepribal/Ref/3DView/Menus/Curve - 版の履歴

Yamyam: 1版 をインポートしました

2012年5月16日 (水) 07:17にwiki>Pepribalによる

Yamyam: 1版をインポートしました