利用者:CleverCoder/Doc:2.6/Manual/Modifiers/Generate/Bevel

提供: wiki
2018年6月29日 (金) 06:09時点におけるYamyam (トーク | 投稿記録)による版 (1版 をインポートしました)
(差分) ← 古い版 | 最新版 (差分) | 新しい版 → (差分)
移動先: 案内検索


Page status (reviewing guidelines)

Page reviewed and in good shape

Bevel Modifier

Mode: Object mode

Panel: Properties Window -> Context Button Modifiers CZ Modifier ContextButton.png

Default bevel.

The Bevel modifier adds the ability to bevel the edges of the mesh it is applied to, allowing control of how and where the bevel is applied to the mesh.

The Bevel modifier is a non-destructive alternative to the Bevel Operation in mesh editing mode.

Unbeveled square.
Beveled square.

The picture Unbeveled square shows a square which has unbeveled edges as the angles between the corners of the square are 90° (perpendicular). The picture Beveled square shows a square which has beveled corners.

Although the two pictures show 2D squares, the Blender Bevel modifier can work on both 2D and 3D meshes of almost any shape, not just squares and cubes…

The picture Default bevel shows a Blender 3D cube with a bevel applied using just the default Bevel modifier settings.

Options

Bevel modifier panel.

Width

The Width numeric field controls the width/amount of the bevel applied to the base mesh. It can range from 0.0 (no bevel applied) to 1.0 (Blender Units). This value is in fact the “backing up” of the two new edges relatively to the original (beveled) one, along the two concerned faces.

Note
When using Metric or Imperial units the Width value has a unit. E.g. when 1 Blenderunit is 1m a useful value is between 0cm and 100cm. When it seems that decreasing the Width has no effect anymore check if the unit changed to m instead of cm.


Three Cubes with 0.1, 0.3 and 0.5 bevel Widths.

Segments

Set the number of bevel segments for round edges/verts.

Only Vertices

The Only Vertices button alters the way in which a bevel is applied to the mesh. When it is active, only the areas near vertices are beveled; the edges are left unbeveled.

Three cubes with 0.1', 0.3 and 0.5 bevel Widths, with Only Vertices option enabled.

Limit Method

This section of the Bevel modifier is used to control where and when a bevel is applied to the underlying mesh. The first row of three buttons (mutually exclusive) controls the algorithm used, and might add some extra options.

None
This button will apply the Bevel modifier to the whole underlying mesh, without any way to prevent the bevel on some edges/vertices.
Bevel modifier with the Angle limit enabled.
Angle
This button will only bevel edges where faces make sharp angles. When selected, it displays the Angle numeric field, used to set the angle above which an edge will be beveled (it is in fact the complementary angle, i.e. 180°-(angle between faces)). When the angle between meeting faces is less than the angle in the slider box, a bevel on those specific edges will not be applied. Similarly, when the angle between two edges is less than this limit, the vertex is not beveled.


Bevel modifier with Weight button active.
Weight
Use bevel weights to determine how much bevel is applied; apply them separately in vert/edge select mode. See Here about adjusting bevel weights. The three options specify what edge weight to use for weighting a vertex.
Average
Uses the average bevel weight at the vertex
Sharpest
Uses the smallest bevel weight at the vertex
Largest
Uses the largest bevel weight at the vertex
Vertex Group
Use a vertex group to determine which parts of the mesh get beveled.


Blender3D FreeTip.png
If a bevel appears to seem "flat" or lacks depth along one axis
A scale transformation may be the cause. Switch back to object mode Mode Selection, and apply your object-level scale transformation using CtrlA.